• This forum has 659 topics, 1,236 replies, and was last updated December 7, 2020 by Nana A.
    • Support Q & A
    • VMware vCenter Server Appliance 6.7 u3a

      Good afternoon, VMware has released vCenter Server Appliance 6.7 u3a to address the following security vulnerability: Sensitive information disclosure vulnerabilities in File-Based Backup and Restore functions (CVE-2019-5537 and CVE-2019-5538). Is vCenter 6.7 u3a supported by Zerto Replication 7.5? Is it safe to upgrade our vCenter servers?

    • People: 2
      Replies: 2
    • October 27, 2019
    • reverse sync question

      I would like to create a new ticket for reverse syncing from target to source Example When we do the move operation from source to target After a week the app team says they want to revert the vm back to the source So would like to know about the reverse syncing

    • People: 2
      Replies: 1
    • October 24, 2019
    • VM shutdown

      Is it possible to move the VM in a shutdown state? If yes, I could not move it as it stopped syncing from Zerto.

    • People: 2
      Replies: 1
    • October 24, 2019
    • Connection host, zerto vm and vra

      Hi, I read from documentation that VRA and hosts must be to same network..is right? While zerto vm management how communicate with hosts and vra? Particular network port? And with vcenter? Thanks

    • People: 2
      Replies: 1
    • October 24, 2019
    • At what point does the physical write happens

      Posting on behalf of David H.   At what point does the physical write to the replication sight happen during normal operations? Your VPG/VM’s are running normally; a change happens to any VM in the VPG, at what point does that change become written to the replicated sight?

    • People: 2
      Replies: 1
    • October 23, 2019
    • Confirmation of steps needed

        Posting on behalf of K. Arun Hello Team, We have some question about the zerto replication and ip change We want to replicate an existing file server vm from old ESX (ESX1) to new ESX (ESX2) using zerto. Once it is replicated we want to move the new ESX (ESX2) to a new physical […]

    • People: 2
      Replies: 1
    • October 23, 2019
    • Zerto and Azure

      Posting this post on behalf of Jason.A I have been reading through the Zerto Virtual Manager Azure Administration Guide and I see we can use Zerto to replicate from a protected site Azure to a recovery site vCenter, but was wondering if you can replicate from a protected site vCenter to a recovery site Azure? […]

    • People: 2
      Replies: 1
    • October 23, 2019
    • MS SQL HA – Clustered

      Dear Support, We have had a client who will be configuring 10 SQL server, 5 VM(s) within two cluster nodes on VMware. Is there any limitation from Zerto perspective (assuming not) or would do you possibly have best practice documentation for SQL HA setup as I can’t seem to find any KB within Zerto’s Knowledge […]

    • People: 2
      Replies: 1
    • October 23, 2019
    • Question on vVol Supportability

      I was looking through the Zerto Interoperability Matrix and noticed that vVols are not supported. Can you clarify what that means? Can’t replicate a VM that is on a vVol? Or, can’t use a vVol as a replication target? Both? Thank you!

    • People: 2
      Replies: 1
    • October 22, 2019
    • Move esx hosts to different clusters

      Posting on behalf of Pablo V. I have a new ESXi 6.7 environment and have Zerto 7.5 up and running. I’d like to create new clusters and move some hosts into new clusters. These hosts already have VRA’s installed and running – although I only have one test VPG at the moment. Does moving ESX […]

    • People: 3
      Replies: 2
    • October 22, 2019
    • Zerto site subnet change

      Hi, We might need to make a Zerto site subnet change which would affect the ZVMs and VRAs for a site that is currently replicating from. Could we pause the VPGs, delete the VRAs, re-IP the ZVM and then deploy the new VRAs? Would we be able to unpause the VPGs and continue with the […]

    • People: 3
      Replies: 2
    • October 22, 2019
    • Zerto in a single VCSA

      Could you give me some guidance on how to install Zerto in a singular 6.7 VCSA? I read the install docs and they appear written more for the old style vCenters. I understand the product and have used it with 5.5 vCenters.

    • People: 3
      Replies: 6
    • October 22, 2019
1 2 3 … 27 28 29 … 42 43 44

You must be logged in to create new topics. Click here to login