• This forum has 412 topics, 1,101 replies, and was last updated December 4, 2020 by Yossi A.
    • VMware
    • Zerto Cloud Connector static routes

      Hi All, I’ve deployed zerto cloud connector for one of our customers. Our CSP deployment has ZVM, ZCM on one network (managemnet) and Z-VRAs on another network (storage). Both networks are routable. ZCC had been deployed with two interfaces: customer facing netwokr and our management one. Unfortunately the static route that we should be able […]

    • People: 5
      Replies: 9
    • December 19, 2017
    • Initial Sync 100% but Still showing Initializing

      Hi Experts, I have one VM (17 TB) in my VPG and initial replication got completed in 24 hours (it was showing 32% in 23 hours but went 100% in last one hour). In Dashboard, VPG health is green and 17TB as protected but VPG status is shown as processing for last 10 hours. Please […]

    • People: 2
      Replies: 1
    • December 11, 2017
    • VRA install does not see DVSwitch networks

      I’ve just been handed an issue where, upon installing a VRA onto a group of ESX hosts (v5.5.u2) the VRA install wizard is unable to see the DVSwitch networks, only the standard switch networks. Networking on this host works as expected, otherwise.   Has anyone encountered this and if so, what was your solution? Regards, […]

    • People: 6
      Replies: 6
    • December 11, 2017
    • Change on CPU / Memory – replication

      Hi all,   Silly question –  If we change the number of CPUs in the production site, does it replicate automatically to the DR / destination site? Do we need to make anything to ensure the change?   We are on the middle of a Synch to a destination site and number of CPUs of […]

    • People: 3
      Replies: 3
    • December 6, 2017
    • Multiple ZVMs and on vCenter

      I am wondering if it is possible to have multiple ZVM setup in the same location, and sync’d to the same vCenter? With the ability to leverage the same storage and hypervisors as the first ZVM? The issue I am trying to get around is that the primary ZVM is having upgrade issues from 5.0 […]

    • People: 2
      Replies: 2
    • December 5, 2017
    • VRA not reporting VMs

      My customer has a remote site with a quite bad connection back to HQ. I managed to install VRAs on the hosts at the site, which took some hours, but the site’s virtual machines are not visible in the ZVM UI. The ZVM is located at HQ. I suspect the connection is the problem here. […]

    • People: 2
      Replies: 5
    • November 29, 2017
    • impact replication to os windows license

      Hi, I want to ask about windows license in virtual machine after live failover. whether to change the license of virtual machine or need a reactivate windows license after live failover? or the windows can run well? Thanks before.

    • People: 2
      Replies: 1
    • November 27, 2017
    • change protected site VRA?

      Hello, Is there any capability to move VM/VPG’s on protected site VRA’s like you can at the recovery site? Zerto does not do a good job of balancing VRA workloads and I would like to balance them out but cannot figure out a way in the UI.   Thanks

    • People: 2
      Replies: 2
    • November 20, 2017
    • New Hosts, New Storage, New Admin

      We are working on a new ESX cluster, and I am not 100% confident in my Zerto abilities. I was not the original installer.   We currently have Zerto VIrtual Rep. 5.5u1 on connected to a Windows based 5.5 vSphere. We will be changing this to a vSphere 6.5u1 appliance. I have 4 new hosts, […]

    • People: 2
      Replies: 3
    • November 15, 2017
    • Moving VM's to new datastores

      Hi, we have a new storage system at the DR site. Now I am moving all VM’s to the new datastores. When I configured the VPG, Zerto is moving the VM’s one at a time to the new datastores. Is it possible to tune this operation and let Zerto relocate multiple VM’s at a time […]

    • People: 2
      Replies: 2
    • October 3, 2017
    • Change Zerto VM pRDM to vRDM

      Hi, We have some Zerto virtual appliances which are using Physical Mode RDMs. We would like to change these to Virtual mode RDMs. Is this a supported change on an existing appliance? Or once deployed is it not supported to make these changes? Usually we would simply power down the VM, delete the disk/pointer file, […]

    • People: 2
      Replies: 2
    • October 3, 2017
    • VM's removed from inventory?

      Not really sure what happened.  I got an alert today that one of my VPG’s was paused because one or more VM’s were removed from inventory… but they weren’t.   Both VM’s from the VPG are in inventory, and up and running.  So I deleted the VPG and then tried to recreate it, but recreation […]

    • People: 4
      Replies: 8
    • September 25, 2017
    • vSAN policy

      Hi folks, I am not seeing this part in the manuals, but perhaps you can help me out: I am looking into using Zerto to protect VMs in a vSAN cluster (vSAN 6.6.1 if it matters) Target for the replication will also be a vSAN cluster. How and where can I specify the SPBM/storage policy […]

    • People: 2
      Replies: 3
    • September 22, 2017
    • "need configuration" error in live Failover

      Hi. When i testing failover in Test mode all OK, but in live failover mode after commit proccces failover aborted  .i find error id (VPG0006)offical suppport page but dont understand what is a problem.After this error failover procces always canceled and journal datastore location always lost  .I select  database again  for journal and repeat live […]

    • People: 3
      Replies: 3
    • September 12, 2017
1 2 3 … 19 20 21 … 26 27 28

You must be logged in to create new topics. Click here to login