• This forum has 412 topics, 1,101 replies, and was last updated December 4, 2020 by Yossi A.
    • VMware
    • Microsoft Support

      Hi, when using Zerto, do I still have the possibility to make Microsoft Callsß In the past we had problems with MS when 3rd party software was used. I know, that there is no client instllaed on the MS machine. Kind regards.

    • People: 2
      Replies: 1
    • January 17, 2017
    • Is 5.0 Update 1 compatabile with ESXi 5.5 u3?

      Are ESXi 5.5 U3 hosts tested with 5.0 Update 1? When I deploy the VRA on a 5.5 U3 host, everything deploys correctly but then vCenter has a repeating cycle of RAM usage warnings and Zerto has a repeating cycle of the VRA not being connected and then connected again. I deleted the VRA and […]

    • People: 2
      Replies: 1
    • January 17, 2017
    • Protect VMware Horizon VDI environment?

      Hi, Does anyone have experience on protecting VMware Horizon VDI environment with Zerto? Our goal is to protect traditional office servers with Zerto, but current floating VDI machines should also be protected somehow to keep the same user experience as in normal non-dr situation. -heikki

    • People: 2
      Replies: 1
    • January 16, 2017
    • ZVR 5.0 Update 1, vSphere 6.5 and VSAN 6.5

      Hi all, Just in-case you weren’t already aware, as of Jan 8th ZVR 5.0 U1 was released which now supports vSphere 6.5, VSAN 6.5 and VSAN 6.2. Go to support & downloads to get it today! Any questions let me know. Thanks, Joshua

    • People: 1
      Replies: 0
    • January 11, 2017
    • serial output

      Hi, sorry about my poor english. I have a linux vm (RHEL7) over ESX. I want to enter kdb mode for debugging, I set the grub.conf file with kgdboc parameterlike this: console=tty0 kgdboc=kbd,ttyS0 when I cause a crash the system goes to kdb mode but I cant see it happens the console just freeze…  I […]

    • People: 2
      Replies: 1
    • January 11, 2017
    • IP renaming on Linux

      Hi all, I was recently installing ZVR5.0 After installation, I began the advised tests listed in the documentation, but I found an issue when renaming NIC’s IP. It happened when the VM had more than a NIC, and when during the setting of VPG only one of them was configured with the new one, leaving […]

    • People: 2
      Replies: 1
    • January 11, 2017
    • Can zerto cause VM performance issues?

      I am being told some of our third party engineers that all of our Virtual Machines are running slower than normal and the possible cause is due to the fact that I just recently installed Zerto. I am not able to replicate their tests and everything looks good on my end. Is it possible for […]

    • People: 2
      Replies: 1
    • January 9, 2017
    • Zerto and Netapp Snap Mirror

      IHAC that wishes to use Zerto to protect workloads however they also have a requirement to use Netapp Snapmirror to protect the same workloads and utilize snap mirror for long term backup. I am not a storage expert by any means. Is this a supportable workable solution? How would Zerto manage a failover when there […]

    • People: 2
      Replies: 2
    • December 28, 2016
    • vCloud 8 1 2

      Hello Now that vCloud Director 8 has been released, will Zerto be supporting is for service providers using it with Zerto to provide DRaaS?  If so, is running vCD8 with vSphere 6 underneath supported? Dave

    • People: 15
      Replies: 23
    • December 7, 2016
    • Test failover time period

      Hi I am new here, sorry if I post duplicate question. I want to ask if I have a VM with a 7 days protection by Zerto, and I trigger a test failover, is there any time limitation of stop the failover test? What happen if I test over 7 days, will it be impact […]

    • People: 2
      Replies: 1
    • November 28, 2016
    • MSCS Cluster – IP Change During Failover

      Hello During recovery of MSCS Cluster ( Active node/system), system failed over to DR site without any issue, but the cluster service did not come up. After reading through the documents, i see Zerto recommends preconfigure listeners on both the protected and recovery IP ranges, each node with a dedicated heartbeat NIC. is there any document […]

    • People: 2
      Replies: 1
    • November 16, 2016
    • VMware permissions not replicated

      We are protecting a VM that has some explicit VMware permissions applied to it tha allow the administrators of the VM access to it.  These permissions are not being replicated to the recovery site. When we test the failover, the owner of the VM no longer has access though vSphere. Has anyone else seen this […]

    • People: 2
      Replies: 1
    • November 2, 2016
1 2 3 … 23 24 25 26 27 28

You must be logged in to create new topics. Click here to login